| Server IP : 49.231.201.246 / Your IP : 216.73.216.149 Web Server : Apache/2.4.18 (Ubuntu) System : User : root ( 0) PHP Version : 7.0.33-0ubuntu0.16.04.16 Disable Function : exec,passthru,mail,shell_exec,system,proc_open,popen,ini_alter,dl,proc_close,curl_exec,curl_multi_exec,readfile,parse_ini_file,escapeshellarg,escapeshellcmd,show_source,pcntl_alarm,pcntl_fork,pcntl_waitpid,pcntl_wait,pcntl_wifexited,pcntl_wifstopped,pcntl_wifsignaled,pcntl_wifcontinued,pcntl_wexitstatus,pcntl_wtermsig,pcntl_wstopsig,pcntl_signal,pcntl_signal_get_handler,pcntl_signal_dispatch,pcntl_get_last_error,pcntl_strerror,pcntl_sigprocmask,pcntl_sigwaitinfo,pcntl_sigtimedwait,pcntl_exec,pcntl_getpriority,pcntl_setpriority,pcntl_async_signals,pcntl_unshare,mail,php_uname,phpinfo MySQL : OFF | cURL : ON | WGET : ON | Perl : ON | Python : ON | Sudo : ON | Pkexec : ON Directory : /usr/share/webmin/net/ |
Upload File : |
#! /bin/sh
#
# rc.inet1 This shell script boots up the base INET system.
#
# Version: @(#)/etc/rc.d/rc.inet1 1.01 05/27/93
#
HOSTNAME=`cat /etc/HOSTNAME`
# Attach the loopback device.
/sbin/ifconfig lo 127.0.0.1
/sbin/route add -net 127.0.0.0 netmask 255.0.0.0 lo
# IF YOU HAVE AN ETHERNET CONNECTION, use these lines below to configure the
# eth0 interface. If you're only using loopback or SLIP, don't include the
# rest of the lines in this file.
# Edit for your setup.
IPADDR="10.2.6.2" # REPLACE with YOUR IP address!
NETMASK="255.255.0.0" # REPLACE with YOUR netmask!
NETWORK="10.2.0.0" # REPLACE with YOUR network address!
BROADCAST="10.2.255.255" # REPLACE with YOUR broadcast address, if you
# have one. If not, leave blank and edit below.
GATEWAY="10.2.5.111" # REPLACE with YOUR gateway address!
# Uncomment the line below to configure your ethernet card.
/sbin/ifconfig eth0 ${IPADDR} broadcast ${BROADCAST} netmask ${NETMASK}
# If the line above is uncommented, the code below can also be uncommented.
# It sees if the ethernet was properly initialized, and gives the admin some
# hints about what to do if it wasn't.
if [ ! $? = 0 ]; then
cat << END
Your ethernet card was not initialized properly. Here are some reasons why this
may have happened, and the solutions:
1. Your kernel does not contain support for your card. Including all the
network drivers in a Linux kernel can make it too large to even boot, and
sometimes including extra drivers can cause system hangs. To support your
ethernet, either edit /etc/rc.d/rc.modules to load the support at boottime,
or compile and install a kernel that contains support.
2. You don't have an ethernet card, in which case you should comment out this
section of /etc/rc.d/rc.inet1. (Unless you don't mind seeing this error...)
END
fi
# Uncomment this to set up your gateway route:
if [ ! "$GATEWAY" = "" ]; then
/sbin/route add default gw ${GATEWAY} netmask 0.0.0.0 metric 1
fi
# End of rc.inet1